Download a Suzuki outboard repair manual instantly. A downloadable Suzuki boat motor repair manual, also termed Suzuki outboard online factory service manual (FSM) or Suzuki engine workshop manual, is a digitally transmitted handbook giving instructions on how to overhaul, service or restore the motor back to working order. Download A Factory Suzuki 4-Stroke Or 2-Stroke outboard engine repair manual In just seconds, get the information you need now to fix your problems! Coveres All DF & DT models of all years. Suzuki Service Repair Manual Free PDF sv650, rm250, gs500, dl1000, gn250, bandit, vl800, dl650, gz250, intruder, sv1000, gs550, gladius, rm125, dr350.
RELATED SUZUKI OUTBOARD SEARCHES:
PROPELLERS
An outboard motor is designed to develop its rated power within a specified engine speed range. The maximum rated power delivered by the Suzuki models are shown in your service manual. If the standard propeller fails to meet the above requirement, use another pitch propeller to hold the engine speed within the range specified in your manual propeller selection chart.
Installing a propeller with pitch either too high or too low will cause incorrect maximum engine speed, which may result in severe damage to the motor.
Installing a propeller with pitch either too high or too low will cause incorrect maximum engine speed, which may result in severe damage to the motor.
Disassembly of propeller shaft components
1. Slide propeller shaft away from reverse gear housing assembly
Account for reverse gear back-up shim thrust washer
2. Remove horizontal slider and forward gear thrust washer
3. Remove spring
4. Using special tool, push dog pin shifter.
5. Remove clutch dog shifter propeller shaft.
PROPELLER
• Inspect propeller for bent, chipped or broken blades and replace or repair if necessary.
• Inspect propeller bushing splines for wear or other damage and replace if necessary.
• Inspect propeller bushing for deterioration or slipping and replace if necessary.
PROPELLER SHAFT COMPONENTS
• Inspect horizontal slider and connector pin for excessive wear or other damage. Replace if necessary.
• Inspect clutch dog shifter for excessive wear, chip or other damage. Replace if necessary.
• Inspect dog pin for bent or other damage. Replace if necessary.
• Inspect propeller shaft / splines for wear, twist or other damage. Replace if necessary.
PROPELLER SHAFT BEARING HOUSING
• Inspect housing for cracks or other damage. Replace if necessary.
Mercedes benz photos download. • Inspect propeller shaft bearings and reverse gear bearing for pitting, rough or other damage. Replace if necessary.
• Inspect oil seals and O-ring for cuts, nicks or tears.
Replacing propeller shaft oil seal
1. Remove retaining ring
2. Extract oil seals
1 and washer 2.3 using oil seal remover.
Do not re-use oil seal once removed.
Always use a new oil seal.
3. Apply Water Resistant Grease to inner circumference of housing.
Free Download Suzuki Dt150 Service Manual Download
4. Using an oil seal installer, drive two oil seals (one at a time) into housing.
The lipped portion of seal should face towards propeller.
Apply Water Resistant Grease to seal lips.
5. Install washer and retaining ring.
PROPELLER INSTALLATION
1. Install spacer shaft, then slide on propeller
2. Fit spacer specified torque.
1 and propeller stopper 2 onto propeller3.4, washer 5 and nut 6, then tighten nut to
Propeller nut : 55 N.m (5.5 kg-m, 40.0 lb.-ft.)
3. Push cotter pin secure.
PROPELLER SELECTION FOR COUNTER
ROTATION Where can i find a free download repair manual for a 2004 honda pilot.
For counter-rotation model, newly designed stainless steel propellers are available as follows.
Mazda 3 manual download. These cars are equipped with Z6 gasoline engines (1.6 l.), LF-DE (2.0 l.), L3-VE (2.3 l.), L3-VDT (2.3 l. Mazda 3 service manual, operation, owner’s and maintenance manuals.
Suzuki highly recommend to use the genuine Suzuki counterrotation propeller for the counter rotation model. In case of twin installation, always use on both engines, the same size normal rotation and counter-rotation propellers.
ENGINE CRANKED, BUT NOT START (OR STOPS SHORTLY AFTER STARTING)
UNSTABLE IDLING / TROLLING (OR ENGINE TENDS TO STALL)
UNSTABLE IDLING / TROLLING (OR ENGINE TENDS TO STALL)
• Incorrect by-pass air screw adjustment [NOTE3]
• IAC valve failure [NOTE3]
• IAC passage failure (clogged hose, etc.) [NOTE3]
• Spark plug failure
• Ignition coil failure
• ECM failure
• Wire continuity / connection failure
• Failure of high pressure fuel system components :
• Fuel injector (clog, stuck valve, etc.)
• Fuel pressure regulator (incorrect regulated pressure, etc.)
• Fuel pump (clogged suction filter, leakage in tank, etc.)
• Fuel filter (clog, etc.)
• Hose (clog, kink, leakage, etc.)
• IAC valve failure [NOTE3]
• IAC passage failure (clogged hose, etc.) [NOTE3]
• Spark plug failure
• Ignition coil failure
• ECM failure
• Wire continuity / connection failure
• Failure of high pressure fuel system components :
• Fuel injector (clog, stuck valve, etc.)
• Fuel pressure regulator (incorrect regulated pressure, etc.)
• Fuel pump (clogged suction filter, leakage in tank, etc.)
• Fuel filter (clog, etc.)
• Hose (clog, kink, leakage, etc.)